PIVOT Bed is available in various sizes. These sizes correspond to the standard local mattress sizes in each territory. While some measurements are identical across all sizes, many are different so we’ll provide the standard measurements first and then break into individual bed sizes. As international mattress sizes vary, and names for them vary, we'll provide measurements for each mattress size in each dimension – length and width.
All height measurements don't include any mat solution, including our own which we’ll provide separately.
Standard Measurements (in inches and millimeters)
-
Distance from the wall behind the headboard to the tip of the base unit sides, which remain in place at all times: 41.7" (1060mm)
Note the design reaches over any base/skirting-board so ignore these if you have them.
- Top of the wall mount (so where any wall-mounted headboard is free to start from): 23.6" (600mm)
- Rear wall to the ‘underside’ of the mattress panels when bed is vertical: 16.1" (410mm)
-
Floor to underside of mattress panels when horizontal (storage space): 12" (306mm)
Note the under-bed storage space is non-uniform and this measurement is the most commonly available space.
- Floor to bottom of mattress: 12.7" (324mm)
Note: to find how high the top of *your* mattress will sit when horizontal add the thickness of your mattress to the above measurement.
-
Power rack uprights outside-to-outside: 45.3" (1150mm)
Note: power rack width does NOT differ between mattress/bed sizes
Width Measurements for 63" (1600mm) wide mattresses (e.g. EU king)
- Available width within frame for mattress: 63" (1600mm)
-
Outside-to-outside of the base unit metalwork: 69.5" (1767mm)
Note there are some screw heads which extend about 0.2" (5mm) more on each side.
- Total width of the frame at the foot end, at the ‘legs’: 65.5" (1666mm)
Width Measurements for 59" (1500mm) wide mattresses (e.g. UK king, US queen)
- Available width within frame for mattress: 59" (1500mm)
-
Outside-to-outside of the base unit metalwork: 66" (1667mm)
Note there are some screw heads which extend about 5mm more on each side.
- Total width of the frame at the foot end, at the ‘legs’: 61.6" (1566mm)
Width Measurements for 53.1", 53.5" & 55.1" (1350, 1360 & 1400mm) wide mattresses (e.g. UK, US, EU double)
- Available width within frame for mattress: 55.1" (1400mm)
-
Outside-to-outside of the base unit metalwork: 62" (1567mm)
Note there are some screw heads which extend about 0.1" (5mm) more on each side.
- Total width of the frame at the foot end, at the ‘legs’: 57.7" (1466mm)
Length/height measurements for 80.7" (2050mm) long mattresses (e.g. US queen):
- We have found that a snug fit is best so we have rationalised this frame length to the same as the 2000mm version, as below.
- We have reached this decision following extensive feedback from North American customers who have almost universally reported a gap at the foot of the mattress, which is accentuated by the mattress compressing slightly when vertical.
Length/height measurements for 2000mm long mattresses (e.g. UK & EU king, EU double):
- Available length within frame for mattress: 78.7" (2000mm)
- Rear wall to foot of bed when horizontal: 84.6" (2150mm)
- Floor to highest point of bed frame when vertical: 84.6" (2150mm)
- Maximum height of pull-up bar (centre of bar): 90.7" (2305mm)
- Minimum height of pull-up bar (centre of bar): 82.6" (2100mm)
- Height of power rack uprights (unextended): 84.6" (2150mm)
- Max height of extended power rack pull-up bar (centre of bar): 96.6" (2455mm)
Length/height measurements for 74.8" (1900mm) long mattresses (e.g. UK & US double):
- Available length within frame for mattress: 74.8" (1900mm)
- Rear wall to foot of bed when horizontal: 80.7" (2050mm)
- Floor to highest point of bed frame when vertical: 78.9" (2005mm)
- Maximum height of pull-up bar (centre of bar): 86.8" (2205mm)
- Minimum height of pull-up bar (centre of bar): 78.7" (2000mm)
- Height of power rack uprights (unextended): 80.7" (2050mm)
- Max height of extended power rack pull-up bar (centre of bar): 92.7" (2355mm)
Mat measurements
The PIVOT Multi-layer Exercise Mat has two layers if placed on carpet. The wooden layer is optional if the mat is placed on a strong, hard floor. You should add the thicknesses together for the layers suitable for your flooring. The size of the mat does not vary by bed size and if required it can be cut to size easily by the customer.
We do not recommend any mat that doesn’t extend to the full size of the bed when horizontal and we do not recommend foam mats for any heavy equipment.
- Thickness of top layer (natural rubber): 7mm
- Thickness of wooden (OSB3) layer: 11mm
- Total length: 2250mm
- Total width: 2000mm